| Characteristic |
Description |
 | |
| Base Configuration | HPE ProLiant DL345 Gen10 Plus, article number P39267-B21 |
| Form Factor | 2U, rack mountable |
| CPU | AMD EPYC 7443P processor, operating frequency 2.85-4.0 GHz, 24 cores, L3 cache 128MB, 200W
Maximum number of processors per server - 1
Maximum effective RAM frequency supported by the processor, 3200 MT/s
Maximum amount of RAM supported by the processor, 4TB |
| Chipset | System on Chip (SoC) design |
| RAM | Preinstalled 32 GB memory: 1 HPE 32GB (1x 32GB) Double Rank x4 DDR4-3200 CAS-22-22-22 Registered Smart Memory Kit
Supported memory types:
HPE SmartMemory DDR4 Registered DIMM (RDIMM) - up to 32 modules
HPE SmartMemory DDR4 Load Reduced DIMM (LRDIMM) - up to 32 modules
Maximum RAM 4092 GB (16x256 GB) for LRDIMM, 1024 GB (16x64 GB) for RDIMM
Eight-channel memory controller integrated into the CPU: 16 slots per server, 16 slots per CPU, 2 modules per channel
Memory operating frequency 3200 MT/s (1 DPC), 3200 MT/s (2 DPC), DPC - DIMM Per Channel
Maximum memory subsystem bandwidth of 205 GB/s (per CPU)
Support for HPE SmartMemory technology |
| Disk subsystem | Installed basket (Bay-3:
Up to 8 Hot Plug 2.5" SFF SAS/SATA HDD/SSD hot-swappable drives, connected to P408i-a SAS module
Additional baskets (optional in Bay-2andBay-1, possible options):
- Hot Plug 2.5" SFF SAS/SATA HDD/SSD hot-swappable cage (RAID controller required)
- Hot Plug 2.5" SFF SAS/SATA/NVMe x4 Tri-Mode 24G U.3 hot-swappable cage (Tri-Mode controller and cable set required)
- Hot Plug 2.5" SFF SAS/SATA/NVMe x1 Tri-Mode 24G U.3 hot-swappable cage (Tri-Mode controller and cable set required)
- Hot Plug 2.5" SFF NVMe 16G U.2 hot-swappable cage replacement (requires a set of cables for direct connection to the motherboard)
Additional cage for the rear panel:
- Cage for 2 Hot Plug 2.5" SFF SAS/SATA/NVMe x4 Tri-Mode 24G U.3 HDD/SSD drives with hot swap (Tri-Mode controller)
Installed drives: no
Total up to 26 2.5" SFF SAS/SATA/NVMe U.3 drives, up to 24 NVMe U.2 drives.
Additional up to two boot drives M.2 PCIe 3.0 x4 22110:
- via an expansion card in any PCIe slot (the board has 2 M.2 PCIe 3.0 x4 slots, built-in RAID controller with RAID 1 support);
OR
Additional up to two boot drives M.2 SATA 2280:
- via expansion card in any PCIe slot (HPE Universal SATA HHHL M.2 Kit) |
| Disk subsystem controller | HPE Smart Array P408i-a 12Gb SAS Controller RAID Module (RAID 1/10/5/50/6/60/HBA) 8 Ports Internal, 2GB Cache
Connected to the main 8-drive SAS/SATA enclosure
A battery is installed to protect the controller's cache memory
Additionally:
HPE Smart Array RAID controller in an expansion slot for connecting additional disk enclosures for SAS/SATA drives (cables are required)
Tri-Mode controller in an expansion slot or a connector on the motherboard for connecting additional disk enclosures for SAS/SATA/NVMe x4/x1 Tri-Mode 24G U.3 drives (cables are required) |
| Network controller | Installed HPE Ethernet 10Gb 2-port BASE-T Broadcom BCM57416 OCP3 Adapter Replacement I/O Module
Additional network adapters in expansion slots
1GbE management port (Dedicated iLO management port) |
| Expansion slots | Two bays for installing riser cards (all x8 slots have an x16 connector)
Possible riser card options for the Riser-1 bay:
- Riser card for 2 PCIe 4.0 slots: x16 FHHL, x16 FHFL (installed by default);
- Riser card for 1 PCIe 4.0 slot: x16 FHFL (slot 2), 4 PCIe 4.0 x4 ports for NVMe drives (2 x SLIMLINE x8);
Possible riser card options for the Riser-2 (optional):
- Riser card for 2 PCIe 4.0 slots: x8 FHHL, x8 FHHL;
- Riser card for 1 PCIe 4.0 slot: x16 FHFL (slot 1);
- Riser card for 4 PCIe 4.0 x4 ports for connecting NVMe drives (2 x SLIMLINE x8); |
| Optical storage | External only via USB port |
| Interfaces | Front: 1 x USB 3.1, iLO Service Port
Rear: 2 x USB 3.1, DB-15 Video, 4 x 1GbE 1000BASE-T, 1GbE RJ-45 Management, Serial (optional)
Internal Ports: 1 x USB 3.1 |
| Video adapter | Integrated video standard, 1920 x 1200 @ 60 Hz (32 bpp)
Up to 3GPU HPE NVIDIA A10 Graphics Accelerator |
| Power Unit | x HPE 800W Hot-Swappable Redundant Platinum-level Power Supply (94%) OR
2 x HPE 800W/1600W Hot-Swappable Redundant Platinum-level Power Supplies (94%) |
| Cooling | hot-swappable, redundant, controllable system fans
Optional: High-efficiency cooling system, required when selecting certain additional options |
| Supported Operating Systems | Windows Server 2016
Windows Server 2019 (Most Recent Version)
VMware ESXi 6.7 U3
VMware ESXi 7.0 U1/U2
SUSE Linux Enterprise Server (SLES) 12 SP5
SUSE Linux Enterprise Server (SLES) 15 SP2
Red Hat Enterprise Linux (RHEL)
? AMD EPYC 7003 Series: 8.3
? AMD EPYC 7002 Series: 7.6, 8.0 |
| Rack mount installation | Set of retractable rails
Additionally:
- cable organizer
- front panel cover to prevent unauthorized access |
| Built-in controls | HPE iLO (HPE Integrated Lights-Out) 4GB NAND, Firmware HPE iLO5 - status monitoring, alerts and reports, remote management
UEFI - secure server configuration and boot in accordance with the industry standard Unified Extensible Firmware Interface (UEFI)
HPE RESTful API - application developer interface
Intelligent Provisioning - a tool for automated deployment of server infrastructure
Embedded Remote Support - built-in remote support tools that provide automatic transmission of information about hardware events to HP service departments |
| BIOS | HPE Server Unified Extensible Firmware Interface (UEFI) |
| Dimensions | Height 8.75 cm, Width 44.54 cm, Depth 71.1 cm |
| Weight | Minimum 16 kg, maximum 23 kg |
| Power supply | 100/240 VAC, 6.7/3.3 A, 50/60 Hz |
| Operating Environment | Operating temperature from +10°C to +35°C, humidity no more than 90%
Storage temperature from -30°C to +60°C, humidity no more than 95%
Humidity no more than 90% |
| Noise level | Idle - 32 dBa
Under load - 35 dBa |
| Warranty | 1 year warranty, service center |